This is a quick reference of how the SCADAPack RTU and device are to be field wired.
SCADAPack 357
Note that SCADAPack 357 is actually a combination of SCADAPack 5606 and SCADAPack 350.
SCADAPack 350
The diagram below outlines the SCADAPack 530 board layout board. Images from “SCADAPack 350 Installation, Operation and Maintenance Setup Manual”, page 15.
This is how you would field wire the SCADAPack 350 analog input for current and voltage applications. Images from “SCADAPack 350 Installation, Operation and Maintenance Setup Manual”, page 28.
This is how you would field wire the SCADAPack 350 analog output. Images from “SCADAPack 350 Installation, Operation and Maintenance Setup Manual”, page 31.
This is how you would field wire the SCADAPack 350 digital I/O.
Digital I/O point 0 is shown connected to a 12V load that uses the same 12V power supply that powers the SCADAPack 350. Digital I/O point 4 is shown connected to a 24V load and external 24V power supply. Digital I/O point 2 is shown monitoring a dry contact. Digital I/O point 5 is shown monitoring an open collector contact.
Images from “SCADAPack 350 Installation, Operation and Maintenance Setup Manual”, page 37.
This is how you would field wire the SCADAPack 350 counter. Images from “SCADAPack 350 Installation, Operation and Maintenance Setup Manual”, page 38.
SCADAPack 5606
The diagram below outlines the SCADAPack 5606 I/O layout board. Images from “SCADAPack E 5606 I/O Hardware Manual”, page 8.
This is how you would field wire the SCADAPack 5606 digital input for DC and AC applications. Images from “SCADAPack E 5606 I/O Hardware Manual”, page 28-29.
This is how you would field wire the SCADAPack 5606 digital output for DC and AC applications. Images from “SCADAPack E 5606 I/O Hardware Manual”, page 30.
This is how you would field wire the SCADAPack 5606 analog output. Images from “SCADAPack E 5606 I/O Hardware Manual”, page 24.
SCADAPack 5304
This is how you would field wire the SCADAPack E5304 Analog Output. Picture from “SCADAPack E5304 Analog Output Hardware Manual”, page 9.
SCADAPack 334
The diagram below outlines the SCADAPack 334 layout board. Images from “SCADAPack 334 Hardware Manual”, page 18.
This is how you would field wire the SCADAPack 334 digital input. Images from “SCADAPack 334 Hardware Manual”, page 94.
This is how you would field wire the SCADAPack 334 digital output. Images from “SCADAPack 334 Hardware Manual”, page 97.
This is how you would field wire the SCADAPack 334 analog input. Images from “SCADAPack 334 Hardware Manual”, page 101.
The graphic below shows several examples for wiring of loop-powered and self-powered transmitters with
the corresponding analog inputs set to voltage mode with a 0…5 Vdc measurement range.
Example 1: Channel 0 has a loop powered current transmitter connected to the external power supply.
Example 2: Channel 1 has a self-powered voltage transmitter connected to the external power supply.
Channels 2 through 6 are unused.
Example 3: Channel 7 has a self-powered current transmitter connected to the external power supply.
This is how you would field wire the SCADAPack 334 analog output. Images from “SCADAPack 334 Hardware Manual”, page 106.
The following figure illustrates the power supply configurations for isolated and non-isolated analog
outputs.
This is how you would field wire the SCADAPack 334 counter. Images from “SCADAPack 334 Hardware Manual”, page 83.
Reference